At this point something has changed and we finally managed to reach the machine both via telnet and via Videohub Control.Īt this point we changed the ip to insert again the video hub on our LAN with private addressing (10.102.214.*). We changed the IP of the videohub bringing it back to the 192.168.10.x network default and relaunched the setup for the umpteenth time. Finally we made one last attempt which proved to be decisive. We coudn't take remote control either via telnet or via IP with Blackmagic Videohub Control software. ![]() The problem has been partially solved and the causes identified.įor your information, we send you the details of the troubleshooting performed.Īt first we tried unsuccessfully to reach the videohub from multiple PCs with windows 10 enterprise, even connecting the videohub directly to the PC to avoid possible problems due to the network switch. Has anybody haved a similar issue? Do you have any suggestion? Or can we force a new software/firmware installation, even if the latest version is (formaly) already installed? Is it possibile to force a harware factoy reset ? If so, how? Right now we only can switch video input and output from its frontal panel, but without software we cannot change signal labels, we cannot see the signal routing, nor control the device remotely, so it is a very unhandy and uncompleted workflow for us. We are not able to upgrade nor downgrade the software, so we are stuck at this point. No firewall is active neither our PC, nor on our LAN. It looks like the switch has its IP ports closed (except for ping requests). 7.0.1 and 6.4.4, but this is not possibile, because the updater shows up the error "incompatible software version" and stops the installation, since the latest version is already installed.Įven the VideoHub Setup software cannot find the switch on the network, only on USB. We then tried to downgrade the software to v. It responds to ping requests, but it doesn't respond to VideoHub Control Software request (it keeps searching for the switch forever). Since then, we cannot control anymore the switch on the network. We updated the Switch software to version 7.0.3 with no errors. We properly set the switch IP address, mask and gateway. SDI Metadata Support: Video payload identification ancillary data as per SMPTE 352M.We recently bought a Smart Videohub CleanSwitch 12x12 and installed its VideoHub Control software.SDI Auto Switching: Automatically selects between 270Mb SD SDI, 1.5G HD SDI, 3G level A and level B HD-SDI, 6G HD SDI, 12G SDI and DVB ASI on each input so that each input can be running a different television standard.SDI Color Space: REC 601, REC 709, REC 2020.SDI Color Precision: 10, 12 bit RGB 4:4:4 in all HD and 2K modes, Ultra HD modes up to 2160p30 and 4K modes up to 4Kp30 DCI.SDI Video Sampling: YUV 4:2:2 and RGB 4:4:4.SDI Audio Sampling: Television standard sample rate of 48kHz and 24-bit.SMPTE 259M, SMPTE 292M, SMPTE 296M, SMPTE 372M, SMPTE 424M, SMPTE 425M level A and B.3 Year Limited Manufacturer's Warranty, and 12 Month Warranty on the front panel 1.Welcome wallet with QR code for software download 1. ![]() ![]() Customize Router Control with the Developer SDK.Get Router Control on Mac, Windows and iPad.Advanced 12G-SDI for SD, HD and Ultra HD Routing.Blackmagic Design Videohub 10x10 12G Features It also features SDI re-clocking, external Ethernet control and supports all SDI video standards up to 2160p60. Routing can be performed by direct button selection and using the large spin knob control that has an electronic clutch. ![]() The front panel LCD lets you see video before routing and clearly displays routing labels and video standards. It has 10 12G-SDI inputs and 10 12G-SDI outputs plus reference connections in a one rack unit size. Blackmagic Videohub 10x10 12G is an advanced zero latency video router that supports any combination of SD, HD and Ultra HD on the router at the same time.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |